View 27-7402-250-TE_4407683.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

COMMUNICATIONS COMPONENTS
Up to 300 mW Fiber Bragg Grating Stabilized 980 nm Pump Modules with Tight Tracking 2700-TE Series
Key Features
* High kink-free powers to 300 mW * Low-profile, epoxy-free, and flux-free 14-PIN butterfly planar package * Fiber Bragg grating stabilization * Wavelength selection available * Tight tracking of fiber-coupled power * Integrated thermoelectric cooler, thermistor, and monitor diode * High dynamic range * Excellent low power stability
Applications
* Erbium doped fiber amplifiers (EDFAs) without a front-fiber tab for tracking * Dense wavelength division multiplexing (DWDM) EDFAs for small package designs * High bit rate, high channel count EDFAs * CATV distribution
The JDSU 2700-TE Series 980 nm pump module utilizes a planar construction with chip on subcarrier. The high power JDSU laser chip is hermetically sealed in a low-profile, epoxy- and flux-free 14-pin butterfly package and fitted with a thermistor, thermoelectric cooler, and monitor diode. The module meets the stringent requirements of the telecommunications industry, including TelcordiaTM GR-468-CORE for hermetic 980 nm pump modules. The 2700-TE Series pump module uses fiber Bragg grating stabilization to "lock" the emission wavelength. It provides a noise-free narrowband spectrum, even under changes in temperature, drive current, and optical feedback. Wavelength selection is available for applications that require the highest performance in spectrum control with the highest available powers. The 2700-TE Series design also offers tight tracking of fiber-coupled power via the monitor diode signal.
Compliance
* Telcordia GR-468-CORE
NORTH AMERICA: 800 498-JDSU (5378)
WORLDWIDE: +800 5378-JDSU
WEBSITE: www.jdsu.com
2700-TE SERIES
2
Dimensions Diagram 250 m Bare Fiber Type A Wiring (Note: Specifications in mm unless otherwise noted; tolerance = .x .3, .xx .20 The module pigtail consists of 250 m buffered, Corning PureModeTM HI-1060 Singlemode fiber.)
1600 M I N (1900 NOM )
45.04 30.0
1000 NOM . TO CENTER OF GRATING 26.0 20.8 17.8 1 .5 500 NOM . TO C/L OF SPLICE (OPTIONAL)
4 0 . 5 N O M . 1 5 . 5 1 2 .7
9.0 STRAIN RELIEF
FLEXIBLE <=400 MICRON RECOAT
4.6
4X
2 .5 0 TH RU
1 2X 2 . 5 L E A D S P A C I N G TOLERANCE IS NON-ACCUMULATIVE 14X 0.51 LEAD WIDTH
260 < RECOAT <
935 (MICRON)
2.8 4.0 0 1.50 7.70.20
RED NON-XYLENE MARK FOR RECOAT WITH 295 35 m
3.9
1.5
5 . 6 TO L EA D C/ L
2X ~ 5
5. 26
0.25 LEAD THICKNESS
Pinout
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Description Cooler (+) Thermistor Monitor PD Anode Monitor PD Cathode Thermistor N/C N/C N/C N/C Laser Anode Laser Cathode N/C Case Ground Cooler (-)
7
6
5
4
3
2
1
8
9
10
11
12
13
14
2700-TE SERIES
3
Table 1: Absolute Maximum Ratings
Parameter Operating case temperature Storage temperature LD submount temperature LD reverse voltage LD forward current LD current transient LD reverse current PD reverse voltage PD forward current Electrostatic discharge (ESD) TEC current TEC voltage Axial pull force Side pull force Fiber bend radius Relative humidity Lead soldering time
Symbol Top Tstg TLD Vr
Test Conditions 2000 hours 1 s maximum C = 100 pF, R = 1.5 , human body model 3 x 10 seconds 3 x 10 seconds 40 C 260 C
Minimum -5 C -40 C 0 C 16 mm 5% -
Maximum 75 C 85 C 50 C 2V 650 mA 1000 mA 10 A 20 V 10 mA 1000 V 2.5 A 4.0 V 5N 2.5 N 95% 10 seconds
VPD IPD VESD ITEC VTEC
RH
Note: Absolute maximum ratings are the maximum stresses that may be applied to the pump module for short periods of time without causing damage. Stresses in excess of the absolute maximum ratings can permanently damage the device. Exposure to absolute maximum ratings for extended periods, or exposure to more than one absolute maximum rating simultaneously may adversely affect device reliability.
Table 2: Operating Parameters
(BOL, Tcase = 0 to 75 C, TLD = 25 C, -50 dB reflection, unless noted otherwise)
Product Code1
Maximum Operating Power Pop (mW)2,3
Maximum Operating Current Iop (mA) Maximum2 360 380 400 420 440 460 480 500 520 540 560 560
Minimum Kink-Free Power Pmax (mW)4
Kink-Free Current Imax (mA)3 Maximum4
27-xxxx-190-TE 27-xxxx-200-TE 27-xxxx-210-TE 27-xxxx-220-TE 27-xxxx-230-TE 27-xxxx-240-TE 27-xxxx-250-TE 27-xxxx-260-TE 27-xxxx-270-TE 27-xxxx-280-TE 27-xxxx-290-TE 27-xxxx-300-TE
170 180 190 200 210 220 230 240 250 260 270 280
190 200 210 220 230 240 250 260 270 280 290 300
400 420 440 460 480 500 520 540 560 580 600 600
1. The 29-xxxx-xxx-FL may be substituted for this part series. All 27-xxxx-xxx-TE end product specifications will remain as published; there is no change to part numbers, product testing, quality or reliability. Traceability is accomplished through product serial number. 2. The maximum operating power Pop will be achieved at a device-specific current, the maximum operating current Iop. The individual value of Iop is noted on the hardcopy data sheet shipped with the device. All values of Iop are limited by the maximum value listed in Table 2. 3. The pump laser shall never be operated at a power higher than the maximum operating power Pop throughout its lifetime. At Begin of Life (BOL), the operating current shall never be higher than the device-specific maximum operating current Iop that is noted on the hardcopy data sheet shipped with the device. At End of Life (EOL), the operating current shall never be higher than the device-specific kink-free current Imax that is noted on the hardcopy data sheet shipped with the device. 4. The module is kink-free (at least) up to a minimum kink-free power Pmax that the module will achieve at a device-specific current, the kink-free current Imax. The individual value of Imax is noted on the hardcopy data sheet shipped with the device. All values of Imax are limited by the maximum value listed in Table 2.
2700-TE SERIES
4
Table 3: Available Peak Wavelength Selection (Tamb = 253 C, 50 mW < P < Pop)
Product Code 27-8000-xxx-TE 27-7402-xxx-TE 27-7552-xxx-TE 27-7602-xxx-TE 27-7702-xxx-TE 27-8052-xxx-TE
Minimum Peak Wavelength 970.0 nm 973.0 nm 974.5 nm 975.0 nm 976.0 nm 979.5 nm
Maximum Peak Wavelength 985.0 nm 975.0 nm 976.5 nm 977.0 nm 978.0 nm 981.5 nm
Table 4: Electro-Optical Performance
(BOL,Tcase = 0 to 75 C,TLD = 25 C, -50 dB reflection, unless noted otherwise)
Parameter Threshold current Forward voltage Spectral width Peak wavelength tuning Side-mode suppression ratio Relative optical power stability
Symbol Ith Vf RMS P/amb SMSR
Test Condition If = Iop 50 mW < P < Pop 50 mW < P < Pop 50 mW < P < Pop Peak-to-peak, T = 10 min, 50 kHz sampling, Tcase = 25 C 20 mW < P < Pop 12 mW < P < 20 mW 3.5 mW < P < 12 mW 20 mW < P < Pop1 20 mW < P < Pop2 20 mW < P < Pop Tcase = 75 C Tcase = 75 C Tcase = 75 C Tcase = 75 C, EOL
Minimum 15 dB
Maximum 25 mA 2.5 V 2.0 nm 0.02 nm/C -
Tracking error Tracking ratio Monitor diode responsivity TEC current TEC voltage Thermistor resistance Thermistor constant Module power consumption
TE TR RespBF ITEC VTEC Rth B
-8% 0.90 2 A/mW 9.5 k 3600 K -
4% 10% 25% 8% 1.10 10 A/mW 1.5 A 2.5 V 10.5 k 4200 K 4.5 W 5.5 W
1. The Tracking Error is defined as the normalized change of output power relative to the operating power over case temperature range 0 C to 75 C, at constant back face monitor current corresponding to the operating power at 25 C. 2. The Tracking Ratio is a measure of the front-to-back tracking when the output power is varied. On a plot of optical power versus back-face photocurrent, a straight line is drawn between the minimum power (20 mW) and the operating power Pop points. The tracking ratio is defined as the ratio between measured optical power (shown as data points on the plot) to the value derived from the straight line.
2700-TE SERIES
5
Ordering Information
For more information on this or other products and their availability, please contact your local JDSU account manager or JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide or via e-mail at customer.service@jdsu.com.
Sample: 27-7402-190-TE
27Code 7402 7552 7602 7702 8000 8052 Peak Wavelength 973.0 to 975.0 nm 974.5 to 976.5 nm 975.0 to 977.0 nm 976.0 to 978.0 nm 970.0 to 985.0 nm 979.5 to 981.5 nm
Code 190 200 210 220 230 240 250 260 270 280 290 300
-TE
Minimum Kink-Free Power 190 mW 200 mW 210 mW 220 mW 230 mW 240 mW 250 mW 260 mW 270 mW 280 mW 290 mW 300 mW
User Safety
Safety and Operating Considerations The laser light emitted from this laser diode is invisible and may be harmful to the human eye. Avoid looking directly into the fiber when the device is in operation. CAUTION: THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT INCREASES EYE HAZARD. Operating the laser diode outside of its maximum ratings may cause device failure or a safety hazard. Power supplies used with this component cannot exceed maximum peak optical power. CW laser diodes may be damaged by excessive drive current or switching transients. When using power supplies, the laser diode should be connected with the main power on and the output voltage at zero. The current should be increased slowly while monitoring the laser diode output power and the drive current. Careful attention to heatsinking and proper mounting of this device is required to ensure specified performance over its operating life. To maximize thermal transfer to the heatsink, the heatsink mounting surface must be flat to within .001" and the mounting screws must be torqued down to 1.5 in.-lb. ESD PROTECTION -- Electrostatic discharge (ESD) is the primary cause of unexpected laser diode failure. Take extreme precaution to prevent ESD. Use wrist straps, grounded work surfaces, and rigorous antistatic techniques when handling laser diodes.
2700-TE SERIES
Labeling
21 CFR 1040.10 Compliance Because of the small size of these devices, the output power and laser emission indicator label shown below is attached to the individual shipping container. All labels are illustrated here to comply with 21 CFR 1040.10 as applicable under the Radiations Control for Health and Safety Act of 1968.
14-Pin Module Label
02/09/07 27-ABC123 27-xxxx-xxx-TE Made in China
Shipping Box Label
27-ABC123
Model:
27-xxxx-xxx-TE JDS Uniphase (Shenzhen) Ltd 3 Hongmian Road Futian Free Trade Zone Shenzhen, China 518038 Made in China
Output Power and Laser Emission Indicator Label DANGER
INVISIBLE LASER RADIATION AVOID DIRECT EXPOSURE TO BEAM PEAK POWER 500 mW WAVELENGTH 630 - 1,550 nm CAUTION Handle with care. Easily damaged by electrostatic discharge
INVISIBLE LASER DIODE
AVOID EXPOSURE
This product complies with 21 CFR Chapter 1, Subchapter J
CLASS 3B LASER PRODUCT
Visible/invisible radiation emitted from fiber end or fiber receptacle
NORTH AMERICA: 800 498-JDSU (5378)
WORLDWIDE: +800 5378-JDSU
WEBSITE: www.jdsu.com 2700TEPUMP.DS.CC.AE April 2008
Product specifications and descriptions in this document subject to change without notice. (c) 2008 JDS Uniphase Corporation 10143014 005 0408 PureMode is a registered trademark of Corning Incorporated. Telcordia is a registered trademark of Telcordia Technologies Incorporated.
02/09/07
Serial:

▲Up To Search▲

Price & Availability of 27-7402-250-TE

	To Download 27-7402-250-TE Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .